Custom Fender Strut Kit from Washington Choppers
This Rear Fender Strut Kit is fabricated from 1/2" COLD ROLLED Round Stock steel, then waterjet styled ends to weld to the fender and bolt to your frame. These struts will enhance the lines of your frame.

Works great on our Chop Bob or Street Rod Rolling Chassis. Can use this on either the contoured or Flat Fenders.

RAW - ready for paint or powder coat - $49 for the kit

CHROME Engine Mount Bolt Kit

Here is Washington Choppers own CHROME Hex Engine Mounting Bolt Kit. This is the lower engine bolts for V-Twin engine installation.

#WCEBK - Price - $33.49

Custom Solo Seat Mounts from Washington Choppers

These weld-on Seat Mounts will save you time when mounting one of our solo seats. These percission milled seat mounts are ready to weld to your bike. We use them on all of our Chop Bob line of custom Bobbers. 1 1/4" x 1" with a 1 1/4" curve to mount to your frame. Works great on our frames or anyones frames.
RAW - ready for paint or powder coat - $46 per pair

Washington Choppers Seat Mount Kit

Offered in both Single as well as Dual shock versions. These kits allow you to mount a sprung solo seat using our mini shocks. They feature a powder coated upper bracket that bolts to the two rear mounting studs on our solo seats.

#696741 - Mini Shock Mounitn Kit - Dual - $100
#696742 - Mini Shock Mounitn Kit - Single - $75

Washington Choppers Seat Springs

4" or 5" Mini Solo Seat Shocks used when mountng our solo seats. Available in 4" or 5" lengths. A great way to add our seats to your Retro ride. The adjustab;le shock have a spring ratio of 300lbs/inch. Use with our Single or Dual Shock Mounting Kit.
#696743 - $46 sold each
#696744 - $54 sold each

Washington Choppers Custom Frame Welding Tabs
These welding tabs will save you time behind the bandsaw and grinder. These percission cut tabs are ready to weld to any part of your bike. We use them to weld La Rosa Shocks to frame. There are many uses for these tabs.

They measure 1" wide X 1 1/4" high with a radius to fit 1 1/4" tubing also a 5/16" hole.
RAW - ready for paint or powder coat - $16 for 4

Washington Choppers Custom Welding Tabs
These welding tabs will save you time behind the bandsaw and grinder. These percission cut tabs are ready to weld to any part of your bike. We use them to weld fender struts, oil bag mounts and rear tail light brackets for the Lazer "Micro B" LED lights.

Works great on our frames or anyones frames.
They measure 1" wide X 1 1/4" high with 5/16" hole.
RAW - ready for paint or powder coat - $8 per pair

Have you had trouble finding Good Quality USA Made Stainless Steel Wheel Spacers?
Well we have, so Washington Choppers decided to make our own. These 100% Stainless Steel Wheel Spacers are made from 1040 Stainless steel and work great as custom wheel spacers.

All spacers are .751 I.D. and 1.125 O.D.

Washington Choppers LED Cateye Tail Light & License Plate Bracket

Custom made Steel LED Cateye and License Plate bracket by Washington Choppers - Laser cut for clean, smooth edges.

READY for chrome, paint or powder coat.

Left Side AXLE mounting kit with a slot for a 3/4" Rear Axle.

Washington Choppers LED Cateye Tail Light & License Plate Bracket

Custom made Steel LED Cateye and License Plate bracket by Washington Choppers - Laser cut for clean, smooth edges.

READY for chrome, paint or powder coat.

3/8" FRAME MOUNTING Bracket Kit

Price is $150

Vincent “STOP” Style Taillight. 12V - $150

Washington Choppers LED Cateye Tail Light & License Plate Bracket

Custom made Stainless Steel LED Cateye and License Plate bracket by Washington Choppers - Laser cut for clean, smooth edges.

BRUSHED Stainless Steel. We use them as-is but you can chrome, paint or powder coat them if you wish.

Available in Left Side mounting and has a slot for a 3/4" Rear Axle or 3/8" bolts.

Price is $105